Goldenman Drilling Fluid & Solids-Control Guide

Shale Shaker Screen Size Chart

Compare physical shale shaker screen dimensions for common Derrick, Brandt, M-I SWACO and KEMTRON shaker configurations. This page helps drilling contractors, distributors and procurement teams identify the correct replacement screen family by physical size before final compatibility confirmation.

11screen configurations listed

4major shaker equipment families

mmall dimensions in millimetres

L × W × Hheight shown where applicable

View Replacement Shale Shaker Screens
Send Your Screen Dimensions

Quick Answer:
Common replacement shale shaker screen sizes include 697 × 1053 mm for Derrick FLC2000, 1070 × 570 mm for Derrick Hyperpool, 1165 × 585 × 42 mm for M-I SWACO Mongoose, and 1220 × 720 mm for KEMTRON KTL48. Brandt VSM 300 scalping, primary and secondary positions use different physical screen dimensions, so the exact deck position must be identified before ordering.

Shale Shaker Screen Size Chart

The table below lists the physical dimensions of common replacement screen configurations supplied by Goldenman. Use the chart as a first identification step, then verify the original screen part number, panel thickness, gasket position, locking geometry and shaker deck configuration before production.

Shaker Model / Screen Family	Screen Dimensions
Derrick FLC2000	697 × 1053 mm
Derrick FLC500	1050 × 695 mm
Derrick 626	626 × 710 mm
Derrick Hyperpool	1070 × 570 mm
Brandt VSM 300 Scalping	940 × 686 mm
Brandt VSM 300 Primary	889 × 686 mm
Brandt VSM 300 Secondary	686 × 203 mm
Brandt Cobra	630 × 1250 × 25 mm
M-I SWACO Mongoose	1165 × 585 × 42 mm
M-I SWACO MD-3	622 × 655 mm
KEMTRON KTL48	1220 × 720 mm

Important: Length and width alone do not guarantee interchangeability. Screens with similar outside dimensions can still use different frame heights, sealing positions, locking edges, deck contacts or installation directions.

Derrick Shaker Screen Sizes

Goldenman supplies replacement screen configurations for several commonly used Derrick shaker families. The figures below refer to the physical panel size and should be checked against the existing screen before ordering.

Derrick-Compatible

Derrick FLC2000 Screen Size

697 × 1053 mm

Use this dimension to identify the FLC2000 replacement screen family before verifying the exact panel construction and deck interface.

Derrick-Compatible

Derrick FLC500 Screen Size

1050 × 695 mm

Confirm the installed screen and shaker configuration before final production approval.

Derrick-Compatible

Derrick 626 Screen Size

626 × 710 mm

Physical dimensions should be checked together with the panel edge and locking arrangement.

Derrick-Compatible

Derrick Hyperpool Screen Size

1070 × 570 mm

Verify the existing panel dimensions and deck geometry before ordering a replacement screen.

Brandt Shaker Screen Sizes

Brandt VSM 300 screen dimensions differ by deck position. This is especially important when replacing scalping, primary or secondary screens, because these positions are not physically identical.

Brandt-Compatible

VSM 300 Scalping Screen Size

940 × 686 mm

Brandt-Compatible

VSM 300 Primary Screen Size

889 × 686 mm

Brandt-Compatible

VSM 300 Secondary Screen Size

686 × 203 mm

Brandt-Compatible

Brandt Cobra Screen Size

630 × 1250 × 25 mm

VSM 300 identification tip: always tell the supplier whether the replacement is for the scalping, primary or secondary deck position. “VSM 300 screen” by itself is not enough information to identify the correct physical panel.

M-I SWACO & KEMTRON Shaker Screen Sizes

M-I SWACO-Compatible

Mongoose Shaker Screen Size

1165 × 585 × 42 mm

Confirm the existing panel height, gasket location and locking direction before final replacement approval.

M-I SWACO-Compatible

MD-3 Shaker Screen Size

622 × 655 mm

Measure the existing panel and identify the shaker model before placing a replacement order.

KEMTRON-Compatible

KTL48 Shaker Screen Size

1220 × 720 mm

Use the physical size as a first match, then verify the screen-to-deck interface.

How to Measure a Shale Shaker Screen

If the original part number is missing or unreadable, measure the old panel before disposal. For accurate replacement matching, do not rely on length and width alone.

MEASURE 01Overall Length

MEASURE 02Overall Width

MEASURE 03Finished Height

CHECK 04Locking Edge

CHECK 05Gasket Position

CHECK 06Installation Direction

Record the Physical Panel

Measure the overall length, overall width and maximum finished thickness or height. If the frame has unusual edge geometry, photograph and measure that area as well.

Photograph the Interface

Take clear photos of the top surface, underside, feed end, discharge end, gasket edge and locking side. These details help identify panels with similar outside dimensions.

For faster matching, send shaker brand + exact model + old part number + measured dimensions + clear panel photos.

Can Screens With Similar Dimensions Be Interchangeable?

No. Similar outside dimensions are not enough to prove that two shaker screens are interchangeable.

Why the Same Length & Width May Still Not Fit

Different finished panel height
Different frame-edge profile
Different gasket position
Different wedge or locking geometry
Different feed/discharge orientation

What to Verify Before Ordering

Exact shaker model
Existing screen dimensions
Original part number where available
Photos of both sides of the panel
Deck and locking configuration

Screen Size Is Not Mesh Size

Physical shaker screen size describes the outside panel dimensions, such as length, width and finished height. Mesh size or API screen designation describes separation performance. These are different specifications and should not be used interchangeably when identifying a replacement screen.

This page focuses only on physical screen dimensions. Mesh-size and API-designation selection should be handled separately.

Found the Correct Screen Size?

Send Goldenman the shaker brand, exact model, existing screen dimensions and clear photos. We can review the physical panel configuration and help confirm the compatible replacement screen family before quotation.

View Shale Shaker Screens
Send Screen Dimensions

Shale Shaker Screen Size FAQ

What size is a Derrick FLC2000 shaker screen?

The Goldenman-listed Derrick FLC2000-compatible screen size is 697 × 1053 mm. Final compatibility should still be verified against the existing panel and shaker deck.

What size is a Derrick Hyperpool shaker screen?

The listed Derrick Hyperpool-compatible physical screen size is 1070 × 570 mm.

What size is a Mongoose shaker screen?

The listed M-I SWACO Mongoose-compatible screen configuration is 1165 × 585 × 42 mm.

What size is a Brandt VSM 300 primary screen?

The listed Brandt VSM 300 primary screen size is 889 × 686 mm.

Are VSM 300 scalping, primary and secondary screens the same size?

No. The listed VSM 300 scalping screen is 940 × 686 mm, the primary screen is 889 × 686 mm, and the secondary screen is 686 × 203 mm.

Can two shaker screens with the same length and width be interchangeable?

Not necessarily. Finished height, frame profile, gasket position, locking geometry, deck configuration and installation direction can all affect fit.

How do I measure a replacement shale shaker screen?

Measure the overall length, width and finished height, then record the locking edge, gasket position and installation direction. Clear photographs of both sides are strongly recommended.

What if my shaker model is not listed in the chart?

Send Goldenman the shaker model, old part number if available, measured dimensions and clear screen photos so the panel family can be reviewed for compatibility.

Send Your Shaker Model & Screen Dimensions

If you are replacing an existing screen, send the shaker manufacturer, exact model, panel dimensions and photos. Goldenman can review the physical configuration before quotation.

Request a Technical Quote
View Product Range

Compatibility notice: Derrick, FLC, Hyperpool, Brandt, VSM, Cobra, M-I SWACO, Mongoose, MD-3, KEMTRON, KTL48 and other referenced names or marks are used only to identify compatible equipment and replacement-screen applications. Goldenman supplies aftermarket compatible replacement screens and does not imply affiliation with or endorsement by the referenced OEM manufacturers unless expressly stated in writing.

Shale Shaker Screen Size Chart

Table of Contents

Shale Shaker Screen Size Chart

Shale Shaker Screen Size Chart